Notching Tubing with Plasma Cutter?
Page 1 of 2 12 LastLast
Results 1 to 10 of 13

Thread: Notching Tubing with Plasma Cutter?

  1. #1

    Default Notching Tubing with Plasma Cutter?

    I'm just wondering if anyone has any experience notching tubing with a plasma cutter? Is it feasible? Is the quality as good as with a hole saw notcher? Any tricks or techniques? Jigs? Thanks.
    Travis Sleight
    Saratoga Springs,NY
    KC2QIU

  2. Remove Advertisements
    SpecialStage.com
    Advertisements
     

  3. #2
    into right 2 tightens John Cassidy's Avatar
    Join Date
    Dec 2001
    Location
    Bangor, Maine, USA.
    Posts
    1,641

    Default

    If you have the $ to buy a plasma cutter, buy a notcher from Harbor Freight. They're pretty cheap.

    Problem with the plasms is you'll still have more work getting the joint perfect than with a hole saw unit.

    http://da.harborfreight.com/cpisearc...cher&Submit=Go

    There are more expensive units out there, but if you're making a few cages, that might be the ticket.

    We have one and it works great.

    John

  4. #3

    Default

    I've seen guys notch with a crop saw really well....but plasma cutter? You'd be better off having beavers gnaw on the end of the tubes!

    Andrew

  5. Remove Advertisements
    SpecialStage.com
    Advertisements
     

  6. #4

    Default

    I agree that doing a standard fishmouth with a plasma cutter is pretty questionable, but it can be handy for fitting a tube into another multi-tube joint (particularly when it involves angles that you can't approach with an "ol-joint-jigger"-style notcher). You can use a contour fitting tool (like these: http://www.pipemastertools.com/ ) to get the pattern, and make the initial cut with a plasma cutter - but I find that there's still a good amount of grinding necessary afterwards.

    I did witness a nice CNC plasma tubing notcher setup at a sport aircraft facility in northern Colorado once - the machine simply rotated the tube, and moved a plasma cutting torch (held above the tube in a bracket) longitudinally along the axis of the tube. Seemed to work pretty well.

    --
    Kevin Wenzel
    [email protected]

  7. #5

    Default

    Quote Originally Posted by Phlyan Pan
    I'm just wondering if anyone has any experience notching tubing with a plasma cutter? Is it feasible? Is the quality as good as with a hole saw notcher? Any tricks or techniques? Jigs? Thanks.

    If you have a good plasma cutter, and it's perfectly setup for the specific material, and you are an experienced operator, then I guess a plasma cutter would work. In reality, they usually don't make cuts that are of sufficient quality to finish weld without some grinding or smoothing. I've seen the professional CNC setups do a good job, but that requires a ton of setup, and the quality of the machines is usually far about the standard found in a garage shop.

    A better way is to use a "joint jigger" style hole saw tool. Good ones cost about $150, and work well. We tried a Harbor Freight one this summer and it lasted about 3/4 of a roll cage before it started to fall apart. Maybe okay if you never do one again, but I prefer to spend more and have decent tool than to waste time screwing around with a POS.

    I've also done shallow angle cuts with a sawzall or cut-off wheel, and then a bench grinder. Sometimes I'll take a dressing tool and round the wheel on the grinder in order to better form radiuses on the tube. This makes the wheel useless for anything else, but their cheap. I'll warn you though (and this goes back to your question about the plasma cutter), any time I try to "freehand" a cut like this, I spend 3x the time making the joint, vs. using the jigger. Sometimes it's inevitable, but I wouldn't want to do an entire car this way.

    DEM

  8. #6
    Loose nut behind the wheel mayhem83's Avatar
    Join Date
    Dec 2001
    Location
    stacy, mn, usa.
    Posts
    1,074

    Default

    I have a bender and notcher from Pro Tools. I have had them both over ten years. The models have been updated and improved.

    http://www.pro-tools.com/index.html

    I have been very happy with both items I have.
    Mark Utecht
    "Speed means freedom of the soul." From the film Vanishing Point.

  9. #7
    100 oversquare right bentmettle's Avatar
    Join Date
    Dec 2004
    Location
    Ann Arbor, Michigan
    Posts
    3,473

    Default

    I've rough cut with plasma and then went on to finish up with either a bench grinder or a 4 1/2" grinder.

    Patience is really the key to any method you use.(although if you do use a notcher, a good bimetal holesaw, a rigid setup, and a drill that you can actually run at the correct speed are fairly important)

    I think there is a dos or windows program called "miter.exe" which allows a person to print out a template on paper that wraps around the tube. It's popular with bicycle building people. The downside is that you actually have to know what angle you want to cut beforehand....

  10. #8
    into right 2 tightens John Cassidy's Avatar
    Join Date
    Dec 2001
    Location
    Bangor, Maine, USA.
    Posts
    1,641

    Default

    We're going with the JD2 from one of many vendors: http://vansantent.com/

    Converting it to hydraulic operation following in these footsteps:

    http://reference.toolandfab.com/writ...page/index.htm

    We're planning on using BendTech Pro software:

    http://vansantent.com/Vendor_pages/2020Software.htm

    It has the ability to print out templates for notching.

    Cheers! John

  11. #9
    50 caution yump
    Join Date
    Dec 2001
    Location
    buffalo, ny, usa.
    Posts
    789

    Default

    Use a proper tool. If you want to use a Plasma cutter, you may as well use a oxy/acetylene torch--way too much "clean-up" for either.

  12. #10

    Default

    If I had unlimited funds I would invest in this:

    http://www.mittlerbros.com/Tube_Notcher_Ultimate.htm

    I find making a smooth and consistent cut with hand-held plasma difficult enough in a straight line on a flat surface. I can only imagine how pathetic it would look trying to circumnavigate a tube! But for door "X"'s where the tubes join I would probably use it....in the past its been the chop-saw and grinder technique and it takes forever.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •