Search:

WDC is running a rallycross at the property: ...

Bruce, I was down the rabbit hole of HTs. There's no reason why you can't do a cord for a mobile, as the same thoughts above apply. However, you'll need to make a cable that's a headset to mobile. ...

Kevin,

I run a "homemade" setup, consisting of a Peltor Hi-Viz headset I picked up off of Ebay. The cord was removed and replaced with a 5-Pin Mini-XLR that is pinned the same as the Peltor...

Garth,

As noted, where in the fine state of Penna are you? Tons of folks who are enablers that are likely near by.

Randy, dig around on DI. I'm pretty sure Kevin posted the info in his build thread, and I know I've spoken to it over there too. I'm n a tablet, otherwise I'd go looking for the posts.

Long and...

It's been tried. AFAIK it's also died.

John, the kid went to Lehigh. Probably doesn't understand double shear. Just Iacocco era K-cars.

You may want to talk to the folks from Motorsports of Ottawa as well. Someone, it may have well been Doug, had hard copies of route books from that era at Lanark this year. Somewhere there's a...

Um, unless they are G79s they would NOT have Snell certification. If they're G79's, then SA2010. [Technically the G89 Carbons are SA2005, but with the 8860 cert most folks would go by that].
...

It's called ask/PM Kevin. Chip is a piggyback board developed from the SVX stuff.

It's for the snacks Richard....(remembers that Canadian events barely have time to pee, let alone snack between stages).


glws

Echoing fearless driver, what sites?

It was my understanding that Kempton was given back to BMR to use and Dover isn't really viable for a number of reasons.

Buy a damn Impreza 4door with a 2.2 and WITHOUT ABS. Most of the parts used for the FWD car and be sourced from the AWD car, sans the rear hubs. There are a plethora of them in the junk yards...

Still being sold, you just have to search for Axxis/PBR XBG.

Which rears? Depending on caliper, you can run the 471, 770 or the 1004.

The 770's exist in Raybestos ST41, however they are NOT a cheap option. ...

Can you get the update tubes/gussets for the early FIA/MSA T45 GC8 Custom Cages cage? They should be the "Extras" for the roof X, and the A pillar tubes, as shown in this Circa 2010 diagram.
...

We're looking forward to this Maple Syrup thing as well.

That was my point in the first place Matt/Jason. The original 2.2 that won BRS was a $150 motor off some guys floor (might have been $100, can't remember as Kevin got it before I was co-driving...

I go back to my original comment, buy the AC Hydraulic...

Hold on there a wee second John. I do believe your SuparBiatchinBoingers got their first overall win on a FailWheelDrive 2.2 Subaru. Everyone on the east coast blows up the 2.5s. The 2.2 lasted a...

'93-'95 1.8's


See above

...

Matte or Flat Black paint for the A-Pillar bar(s). The idea is to reduce any chance of reflection/glare.

This is POOR advice. Buy a proper quality tool, and it will hold its value long term, even should you decide to sell it later on. Buy a cheap tool, and you may as well throw it in the trash when...

You're showing your age Anders. They're on to the FT-2900. Same comments do apply as above however. Brad's suggestion of the ICOM is also a good one.

The biggest thing between the two is really...

https://fbcdn-sphotos-h-a.akamaihd.net/hphotos-ak-xpf1/t31.0-8/10623402_10152775655806214_4945541758441523347_o.jpg

Rich's car.